nodemcu v3 ds18b20 - radzio25 - 03-12-2017
Witam,
Chciałem na szybko podłączyć 18b20 do nodecmu v3.
Niestety coś mi nie idzie, niby płytka widzi czujnik i podaje jego id.
Ale jest taki problem że czujnik wskazuje tylko wartość 85C albo 127.5C.
Sprawdziłem na nano v3 i tam wszystko działa, nr id ten sam a temperatura realna i widać reakcję czujnika na bodźce temperaturowe. Działa wszystko prawidłowo. Ostatnim urządzeniem które zamyka test jest nano na którym działają czujniki 18b20 więc nie ma mowy o uszkodzeniu w czasie testowania.
Podłączyłem z rezystorem 4k7 , potem z 2k2 bo na 3v3 podobno dla jednego ds18b20 to 2k2 powinno być ktoś tak radził w internecie.
Proszę o pomoc bo już wyczerpałem pomysły gdzie jest błąd.
Poniżej kod jaki wgrałem na oba scalaki i odpowiedź (jedyna różnica że na nano jest pin 2 a na nodemcu jest D2 - inaczej całkiem nie działa na nodemcu jak bym podłączył pod całkiem inny pin)
Kod: #include <OneWire.h>
#include <DallasTemperature.h>
// Data wire is plugged into port 2 on the Arduino
#define ONE_WIRE_BUS 2
#define TEMPERATURE_PRECISION 9 // Lower resolution
// Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
OneWire oneWire(ONE_WIRE_BUS);
// Pass our oneWire reference to Dallas Temperature.
DallasTemperature sensors(&oneWire);
int numberOfDevices; // Number of temperature devices found
DeviceAddress tempDeviceAddress; // We'll use this variable to store a found device address
void setup(void)
{
// start serial port
Serial.begin(9600);
Serial.println("Dallas Temperature IC Control Library Demo");
// Start up the library
sensors.begin();
// Grab a count of devices on the wire
numberOfDevices = sensors.getDeviceCount();
// locate devices on the bus
Serial.print("Locating devices...");
Serial.print("Found ");
Serial.print(numberOfDevices, DEC);
Serial.println(" devices.");
// report parasite power requirements
Serial.print("Parasite power is: ");
if (sensors.isParasitePowerMode()) Serial.println("ON");
else Serial.println("OFF");
// Loop through each device, print out address
for(int i=0;i<numberOfDevices; i++)
{
// Search the wire for address
if(sensors.getAddress(tempDeviceAddress, i))
{
Serial.print("Found device ");
Serial.print(i, DEC);
Serial.print(" with address: ");
printAddress(tempDeviceAddress);
Serial.println();
Serial.print("Setting resolution to ");
Serial.println(TEMPERATURE_PRECISION, DEC);
// set the resolution to TEMPERATURE_PRECISION bit (Each Dallas/Maxim device is capable of several different resolutions)
sensors.setResolution(tempDeviceAddress, TEMPERATURE_PRECISION);
Serial.print("Resolution actually set to: ");
Serial.print(sensors.getResolution(tempDeviceAddress), DEC);
Serial.println();
}else{
Serial.print("Found ghost device at ");
Serial.print(i, DEC);
Serial.print(" but could not detect address. Check power and cabling");
}
}
}
// function to print the temperature for a device
void printTemperature(DeviceAddress deviceAddress)
{
// method 1 - slower
//Serial.print("Temp C: ");
//Serial.print(sensors.getTempC(deviceAddress));
//Serial.print(" Temp F: ");
//Serial.print(sensors.getTempF(deviceAddress)); // Makes a second call to getTempC and then converts to Fahrenheit
// method 2 - faster
float tempC = sensors.getTempC(deviceAddress);
Serial.print("Temp C: ");
Serial.print(tempC);
Serial.print(" Temp F: ");
Serial.println(DallasTemperature::toFahrenheit(tempC)); // Converts tempC to Fahrenheit
}
void loop(void)
{
// call sensors.requestTemperatures() to issue a global temperature
// request to all devices on the bus
Serial.print("Requesting temperatures...");
sensors.requestTemperatures(); // Send the command to get temperatures
Serial.println("DONE");
// Loop through each device, print out temperature data
for(int i=0;i<numberOfDevices; i++)
{
// Search the wire for address
if(sensors.getAddress(tempDeviceAddress, i))
{
// Output the device ID
Serial.print("Temperature for device: ");
Serial.println(i,DEC);
// It responds almost immediately. Let's print out the data
printTemperature(tempDeviceAddress); // Use a simple function to print out the data
}
//else ghost device! Check your power requirements and cabling
}
}
// function to print a device address
void printAddress(DeviceAddress deviceAddress)
{
for (uint8_t i = 0; i < 8; i++)
{
if (deviceAddress[i] < 16) Serial.print("0");
Serial.print(deviceAddress[i], HEX);
}
}
Nano :
Kod: ⸮Dallas Temperature IC Control Library Demo
Locating devices...Found 1 devices.
Parasite power is: ON
Found device 0 with address: 2883613C040000B5
Setting resolution to 9
Resolution actually set to: 9
Requesting temperatures...DONE
Temperature for device: 0
Temp C: 28.00 Temp F: 82.40
Requesting temperatures...DONE
Temperature for device: 0
Temp C: 28.00 Temp F: 82.40
nodemcu v3:
Kod: Dallas Temperature IC Control Library Demo
Locating devices...Found 1 devices.
Parasite power is: ON
Found device 0 with address: 2883613C040000B5
Setting resolution to 9
Resolution actually set to: 9
Requesting temperatures...DONE
Requesting temperatures...DONE
Temperature for device: 0
Temp C: 85.00 Temp F: 185.00
Requesting temperatures...DONE
Requesting temperatures...DONE
Temperature for device: 0
dla rezystancji 4k7 jest 85C
dla rezystancji 2k2 jest 127.5
brak reakcji na bodźce temperaturowe.
Uprzedzam pytania - tak, bardzo ciepło u mnie w domu i te 28 to prawda. termometr podobnie wskazuje.
Proszę o pomoc, może ktoś się spotkał z podobnym problemem ?
RE: nodemcu v3 ds18b20 - itepe - 07-01-2019
Trochę stary temat, ale może komuś się przyda ta "wiedza
Pewnie w tym masz problem:
#define ONE_WIRE_BUS 2
podajesz GPIO2 dla NodeMcuv3, czyli powinienś podłączyć swój DS do pinu D4 lub zadeklarować
#define ONE_WIRE_BUS D4
Jeśli zaś podłączasz do D2, to powinno być:
#define ONE_WIRE_BUS 4
W NodeMCU v3:
D4 - GPIO2
D2 - GPIO4
Powodzenia
RE: nodemcu v3 ds18b20 - es2 - 08-01-2019
85 stopni, dla DS18B20, to według dokumentacji temperatura, którą odczytuje się po włączeniu termometru do zasilania bez wcześniejszego wydania komendy konwersji temperatury.
127 (-127) stopni, tak zachowują się ułomne Arduinowe programy odczytujące nic, konkretnie, gdy brak termometru na magistrali.
Cała filozofia tej wiedzy, to przeczytanie krótkiej noty DS18B20 i przejrzenie krótkich, niedopracowanych bibliotek Arduino zwłaszcza tej obsługującej DS18B20 ale i znajomość chłamu obsługującego 1-Wire też jest przydatna.
Wszystko to, to 2..3 godziny dla osoby znającej C++, bo zakładam, że zabierając się za programowanie Arduino w C++, język się zna.
|