Koledzy proszę o pomoc bo tracę kolejny dzień i pomysły mi się skończyły.
Chciałbym zaprogramować ATtiny85 przez Arduino UNO używając go jako programatora.
Gdy to robię otrzymuję komunikat
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xff
Podczas ładowania szkicu wystąpił błąd
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xff
Wcześniej na tym komputerze programowałem w ten sam sposób ATtiny13, które wciąż mogę na nim bez problemowo programować, natomiast problem występuje tylko przy ATtiny85
Wgrywałem już różne sterowniki może gdzieś jakiś został i się jakoś gryzie - nie wiem.
Przeinstalowałem Arduino, usunąłem z menagera programów sterowniki, które wcześniej doinstalowałem czytając rady na różnych forach jednak nic to nie dało.
Co ciekawe na innym komputerze mogę to zrobić bez problemu.
Czy ktoś z Was może mi doradzić gdzie szukać problemu
Z góry dziękuję za pomoc.
Chciałbym zaprogramować ATtiny85 przez Arduino UNO używając go jako programatora.
Gdy to robię otrzymuję komunikat
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xff
Podczas ładowania szkicu wystąpił błąd
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xff
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xff
Wcześniej na tym komputerze programowałem w ten sam sposób ATtiny13, które wciąż mogę na nim bez problemowo programować, natomiast problem występuje tylko przy ATtiny85
Wgrywałem już różne sterowniki może gdzieś jakiś został i się jakoś gryzie - nie wiem.
Przeinstalowałem Arduino, usunąłem z menagera programów sterowniki, które wcześniej doinstalowałem czytając rady na różnych forach jednak nic to nie dało.
Co ciekawe na innym komputerze mogę to zrobić bez problemu.
Czy ktoś z Was może mi doradzić gdzie szukać problemu
Z góry dziękuję za pomoc.