ok link się mi się nie skopiował cały
Płytka została wyposażona w dwa układy pracujące na wspólnej magistrali
I2C, jest to zewnętrzna pamięć EEPROM o pojemności 2kBity o adresie 173
(0xAD) dla odczytu i 172 (0xAC)
nie czaje tego jak to odczytać ten eeprom
tak to mi też nic nie mówi poniżej masz schemat łączenia 4 kości i2c do arduino pomierz zobacz jak to u ciebie wygląda adresowanie masz w nocie katalogowej kości
i tutaj masz kod skanera i2c pokaże jakie urządzenia masz podłączone
Kod:
// --------------------------------------
// i2c_scanner
//
// Version 1
// This program (or code that looks like it)
// can be found in many places.
// For example on the Arduino.cc forum.
// The original author is not know.
// Version 2, Juni 2012, Using Arduino 1.0.1
// Adapted to be as simple as possible by Arduino.cc user Krodal
// Version 3, Feb 26 2013
// V3 by louarnold
// Version 4, March 3, 2013, Using Arduino 1.0.3
// by Arduino.cc user Krodal.
// Changes by louarnold removed.
// Scanning addresses changed from 0...127 to 1...119,
// according to the i2c scanner by Nick Gammon
// http://www.gammon.com.au/forum/?id=10896
// Version 5, March 28, 2013
// As version 4, but address scans now to 127.
// A sensor seems to use address 120.
//
//
// This sketch tests the standard 7-bit addresses
// Devices with higher bit address might not be seen properly.
//
#include <Wire.h>
void setup()
{
Wire.begin();
Serial.begin(9600);
Serial.println("\nI2C Scanner");
}
void loop()
{
byte error, address;
int nDevices;
Serial.println("Scanning...");
nDevices = 0;
for(address = 1; address < 127; address++ )
{
// The i2c_scanner uses the return value of
// the Write.endTransmisstion to see if
// a device did acknowledge to the address.
Wire.beginTransmission(address);
error = Wire.endTransmission();
if (error == 0)
{
Serial.print("I2C device found at address 0x");
if (address<16)
Serial.print("0");
Serial.print(address,HEX);
Serial.println(" !");
nDevices++;
}
else if (error==4)
{
Serial.print("Unknow error at address 0x");
if (address<16)
Serial.print("0");
Serial.println(address,HEX);
}
}
if (nDevices == 0)
Serial.println("No I2C devices found\n");
else
Serial.println("done\n");
delay(5000); // wait 5 seconds for next scan
}
działa odczyt miałem zły adres
spoko , ten kodzik skanera taki niepozorny a już mi nieraz uratował kilka godzin bez owocnego klepania
no mocny program a ja się o klepałem trochę i ch....
Witam
Czy istnieje taka możliwość aby wgrać do pamięci atmegi zawartość 4 różnych eepromów 24c04 potem podłączać po i2c eepromy i w zależności od numeru wciśniętego przełącznika wgrywać odpowiedni wsad ?
Pozdrawiam
Jak wlutowana to wymuś reset na układzie który kontroluje pamięc i będziesz mógł ja odczytać.
Mi chodzi o to czy i jak wgrać zawartość eeproma do arduino aby potem co jakiś czas zaprogramować eeproma bez podłączenia do komputera