[Jarewa0606]

Ja ci powiem  dziwne że ci to ardunio przepuszcza... Odwołujesz się do funkcji zanim została zdefiniowana...

np linijka 107
a zdefiniowane w 140 linijce tak nie może być


Zobacz teraz 

Kod:

#include <SPI.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

#define SCREEN_WIDTH 128 // OLED display width, in pixels
#define SCREEN_HEIGHT 64 // OLED display height, in pixels

// Declaration for an SSD1306 display connected to I2C (SDA, SCL pins)
#define OLED_RESET     -1 // Reset pin # (or -1 if sharing Arduino reset pin)
#define OLED_ADDR 0x3C  //defince OLED addres. Default was 0x3D and i thik it was adafruit default. But from aliexpress has onother athres. To find I2C address use I2Scanncer
Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET);


#define RAIN_SENSOR_OPEN 1000
#define RAIN_SENSOR_CLOSE 400
int rainSensorPin[] = {A0, A1, A2, A3, A6}; //rain sesnors pins
int rainSensorValue[] = {0, 0, 0, 0, 0}; //rain sensor values

#define VALVE_OPEN 1
#define VALVE_CLOSE 0
int valvePin[] = {2, 3, 4, 5, 6};
int valveState[] = {VALVE_CLOSE, VALVE_CLOSE, VALVE_CLOSE, VALVE_CLOSE, VALVE_CLOSE};

#define PUMP_PIN 7

void setup() {
  Serial.begin(9600);

  // SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V internally
  if(!display.begin(SSD1306_SWITCHCAPVCC, OLED_ADDR)) { // Address OLED
    Serial.println(F("SSD1306 allocation failed"));
  }

  for(int i = 0; i < 5; i++){
    pinMode(valvePin[i], OUTPUT);
  }
  pinMode(PUMP_PIN, OUTPUT);

  // Clear the buffer
  display.clearDisplay();
  display.setTextSize(1);
  display.setTextColor(SSD1306_WHITE);
  display.setCursor(0, 32);
  display.println("Auto Garden v 0.1.");
  display.display();
  delay(500);

}

void printTableOnLCD(){

  //vertical lines for dashboard
  display.drawLine(01, 01, 01, 31, SSD1306_WHITE);
  display.drawLine(16, 01, 16, 31, SSD1306_WHITE);
  display.drawLine(31, 01, 31, 31, SSD1306_WHITE);
  display.drawLine(46, 01, 46, 31, SSD1306_WHITE);
  display.drawLine(61, 01, 61, 31, SSD1306_WHITE);
  display.drawLine(76, 01, 76, 31, SSD1306_WHITE);
  display.drawLine(91, 01, 91, 31, SSD1306_WHITE);
  //horizontal lines for dashboard
  display.drawLine(01, 01, 91, 01, SSD1306_WHITE);
  display.drawLine(01, 11, 91, 11, SSD1306_WHITE);
  display.drawLine(01, 21, 91, 21, SSD1306_WHITE);
  display.drawLine(01, 31, 91, 31, SSD1306_WHITE);

  //draw water lvl symbol
  display.setCursor(04, 13);
  display.print("W");
  //display.drawBitmap(02, 12, image_water, 5, 5, SSD1306_WHITE);

  //draw valve symbol
  display.setCursor(04, 23);
  display.print("P");
  //display.drawBitmap(02, 22, image_valve, 5, 5, SSD1306_WHITE);

  //draw pupmp symbol
  //display.drawBitmap(65, 1, image_pump, 21, 16, SSD1306_WHITE);

}

void fillTableByData(){
  Serial.print("In fillTableByData ");
  for(int i = 0; i < 5; i++){
    Serial.print(rainSensorValue[i]);
    Serial.print(" ");
    /*
    display.setCursor(18 + 15 * i, 13);
    display.print(rainSensorValue[i]/10, DEC);
    display.setCursor(18 + 15 * i, 23);
    display.print(valveState[i] == VALVE_OPEN ? 1 : 0, DEC);
    */
//    display.drawBitmap(12 + 10 * i, 22, valveState[i] == VALVE_OPEN ? image_on : image_off, 5, 5, SSD1306_WHITE);
  }
  Serial.println();
}

void valveChangeState(int pin, int state){
  valveState[pin] = state;
  digitalWrite(pin, state == 1 ? HIGH : LOW);
}

void turnOnPump(){
  Serial.println("Pump switch on");
  digitalWrite(PUMP_PIN, HIGH);
}

void turnOffPump(){
  Serial.println("Pump switch off");
  digitalWrite(PUMP_PIN, LOW);
}


void openValve(int pin){
  valveChangeState(pin, VALVE_OPEN);
}

void closeValve(int pin){
  valveChangeState(pin, VALVE_CLOSE);
}


void loop() {
  bool isAnyOpenedValve = false;
  Serial.print("In messure loop values: ");
  for(int i = 0; i < 5; i++){
    rainSensorValue[i] = analogRead(rainSensorPin[i]); //read value of 'i' sensor
    Serial.print(rainSensorValue[i]);
    Serial.print(" ");
    if(rainSensorValue[i] >= RAIN_SENSOR_OPEN){ //if value greater or equal open valve thrshole
      openValve(valvePin[i]); //open valve and save them state
      isAnyOpenedValve = true; //indicate that valve is opened
    }
    if(rainSensorValue[i] <= RAIN_SENSOR_CLOSE){
      closeValve(valvePin[i]);
    }
  }
  Serial.println();

  if(isAnyOpenedValve){ //let's check if is any valve opened
    turnOnPump(); //if so then powe up pump! even if was switched on
  }else{
    turnOffPump(); //if no thet power off pump, even if was switched off
  }
  display.clearDisplay();
  //printTableOnLCD();
  fillTableByData();

  display.display();      // Show initial text
  delay(5000);
}