03-10-2015, 23:16
(Ten post był ostatnio modyfikowany: 04-10-2015, 13:01 przez CEO.
Powód edycji: Używamy znaczników kodu
)
Witam,
mam problem z uruchomieniem Ethernet Shield połączonego z Arduino Uno. Po połączeniu obu modułów, dołączeniu kabla LAN podpiętego do routera i wgraniu podstawowego przykładu WebServer nie mogę połączyć się z urządzeniem. Sprawdziłem, adres ip nie jest używany przez inne urządzenie.
Po wgraniu sketcha na płytce Ethernet Shield palą się diody FULLO, 100M, LINK oraz PWR(Ogólnie 3 żółte i czerwona od zasilania). Dioda RX miga. Natomiast dioda TX nie pali się (mignie co jakiś czas). Z tego co wiem TX odpowiada za transmisję danych więc słabo to wygląda. Proszę o wszelkie sugestie co może być nie tak. Zamieszczam sketch:
mam problem z uruchomieniem Ethernet Shield połączonego z Arduino Uno. Po połączeniu obu modułów, dołączeniu kabla LAN podpiętego do routera i wgraniu podstawowego przykładu WebServer nie mogę połączyć się z urządzeniem. Sprawdziłem, adres ip nie jest używany przez inne urządzenie.
Po wgraniu sketcha na płytce Ethernet Shield palą się diody FULLO, 100M, LINK oraz PWR(Ogólnie 3 żółte i czerwona od zasilania). Dioda RX miga. Natomiast dioda TX nie pali się (mignie co jakiś czas). Z tego co wiem TX odpowiada za transmisję danych więc słabo to wygląda. Proszę o wszelkie sugestie co może być nie tak. Zamieszczam sketch:
Kod:
#include <SPI.h>
#include <Ethernet.h>
// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network:
byte mac[] = {
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
};
IPAddress ip(192, 168, 1, 177);
// Initialize the Ethernet server library
// with the IP address and port you want to use
// (port 80 is default for HTTP):
EthernetServer server(80);
void setup() {
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for Leonardo only
}
// start the Ethernet connection and the server:
Ethernet.begin(mac, ip);
server.begin();
Serial.print("server is at ");
Serial.println(Ethernet.localIP());
}
void loop() {
// listen for incoming clients
EthernetClient client = server.available();
if (client) {
Serial.println("new client");
// an http request ends with a blank line
boolean currentLineIsBlank = true;
while (client.connected()) {
if (client.available()) {
char c = client.read();
Serial.write(c);
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank) {
// send a standard http response header
client.println("HTTP/1.1 200 OK");
client.println("Content-Type: text/html");
client.println("Connection: close"); // the connection will be closed after completion of the response
client.println("Refresh: 5"); // refresh the page automatically every 5 sec
client.println();
client.println("<!DOCTYPE HTML>");
client.println("<html>");
// output the value of each analog input pin
for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
int sensorReading = analogRead(analogChannel);
client.print("analog input ");
client.print(analogChannel);
client.print(" is ");
client.print(sensorReading);
client.println("<br />");
}
client.println("</html>");
break;
}
if (c == '\n') {
// you're starting a new line
currentLineIsBlank = true;
}
else if (c != '\r') {
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(1);
// close the connection:
client.stop();
Serial.println("client disconnected");
}
}