13-12-2020, 16:43
Witam potrzebuję przerobić program tak aby przy zapaleniu i gaszeniu każdego stopnia powoli się rozświetlał i powoli gasną
Kod:
// Edit by Serge Niko June 2015
#include <Adafruit_NeoPixel.h>
#define PIN 10
// Parameter 1 = number of pixels in strip
// Parameter 2 = Arduino pin number (most are valid)
// Parameter 3 = pixel type flags, add together as needed:
// NEO_KHZ800 800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
// NEO_KHZ400 400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
// NEO_GRB Pixels are wired for GRB bitstream (most NeoPixel products)
// NEO_RGB Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2)
Adafruit_NeoPixel strip = Adafruit_NeoPixel(150, PIN, NEO_GRB + NEO_KHZ800);
// IMPORTANT: To reduce NeoPixel burnout risk, add 1000 uF capacitor across
// pixel power leads, add 300 - 500 Ohm resistor on first pixel's data input
// and minimize distance between Arduino and first pixel. Avoid connecting
// on a live circuit...if you must, connect GND first.
// Set up Variables
unsigned long timeOut=60000; // timestamp to remember when the PIR was triggered.
int downUp = 0; // variable to rememer the direction of travel up or down the stairs
int alarmPinTop = 3; // PIR at the top of the stairs
int alarmPinBottom = 6; // PIR at the bottom of the stairs
int alarmValueTop = LOW; // Variable to hold the PIR status
int alarmValueBottom = LOW; // Variable to hold the PIR status
int ledPin = 13; // LED on the arduino board flashes when PIR activated
int colourArray[350]; // An array to hold RGB values
int change = 1; // used in 'breathing' the LED's
int breathe = 0; // used in 'breathing' the LED's
void setup() {
strip.begin();
strip.show(); // Initialize all pixels to 'off'
Serial.begin (9600); // only requred for debugging
pinMode(ledPin, OUTPUT); // initilise the onboard pin 13 LED as an indicator
pinMode(alarmPinTop, INPUT_PULLUP); // for PIR at top of stairs initialise the input pin and use the internal restistor
pinMode(alarmPinBottom, INPUT_PULLUP); // for PIR at bottom of stairs initialise the input pin and use the internal restistor
delay (30000); // it takes the sensor 30 seconds to scan the area around it before it can
//detect infrared presence.
for (int i=0 ;i < 350; i++) { // initilise the colourArray to zero
colourArray[i]=0;
}
}
void loop() {
if (timeOut+15700 < millis()) { // idle state - 'breathe' the top and bottom LED to show program is looping
breathe = breathe + change;
strip.setPixelColor(0,0,0,breathe);
strip.setPixelColor(34,0,0,breathe); //***blauw knipperen****
strip.setPixelColor(35,0,0,breathe); //***blauw knipperen****
strip.setPixelColor(69,0,0,breathe);
strip.setPixelColor(70,0,0,breathe);
strip.setPixelColor(104,0,0,breathe);
strip.setPixelColor(105,0,0,breathe);
strip.setPixelColor(139,0,0,breathe);
strip.setPixelColor(140,0,0,breathe);
strip.setPixelColor(174,0,0,breathe);
strip.setPixelColor(175,0,0,breathe);
strip.setPixelColor(209,0,0,breathe);
strip.setPixelColor(210,0,0,breathe);
strip.setPixelColor(244,0,0,breathe);
strip.setPixelColor(245,0,0,breathe);
strip.setPixelColor(279,0,0,breathe);
strip.setPixelColor(280,0,0,breathe);
strip.setPixelColor(314,0,0,breathe);
strip.setPixelColor(315,0,0,breathe);
strip.setPixelColor(349,0,0,breathe);
strip.setPixelColor(350,0,0,breathe);
strip.setPixelColor(384,0,0,breathe);
strip.setPixelColor(385,0,0,breathe);
strip.setPixelColor(419,0,0,breathe);
strip.setPixelColor(420,0,0,breathe);
strip.setPixelColor(454,0,0,breathe);
strip.setPixelColor(455,0,0,breathe);
strip.setPixelColor(489,0,0,breathe);
strip.setPixelColor(490,0,0,breathe);
strip.setPixelColor(524,0,0,breathe);
strip.setPixelColor(525,0,0,breathe);
strip.setPixelColor(559,0,0,breathe);
strip.show();
if (breathe == 25 || breathe == 0) change = -change; // breathe the LED from 0 = off to 100 = fairly bright
if (breathe == 25 || breathe == 0); delay (100); // Pause at beginning and end of each breath
delay(10);
}
//if {
alarmValueTop = digitalRead(alarmPinTop); // Constantly poll the PIR at the top of the stairs
//Serial.println(alarmPinTop);
alarmValueBottom = digitalRead(alarmPinBottom); // Constantly poll the PIR at the bottom of the stairs
//Serial.println(alarmPinBottom);
if (alarmValueTop == HIGH && downUp != 2) { // the 2nd term allows timeOut to be contantly reset if one lingers at the top of the stairs before decending but will not allow the bottom PIR to reset timeOut as you decend past it.
timeOut=millis(); // Timestamp when the PIR is triggered. The LED cycle wil then start.
downUp = 1;
//clearStrip();
topdown(); // lights up the strip from top down
delay(300);
}
if (alarmValueBottom == HIGH && downUp != 1) { // the 2nd term allows timeOut to be contantly reset if one lingers at the bottom of the stairs before decending but will not allow the top PIR to reset timeOut as you decend past it.
timeOut=millis(); // Timestamp when the PIR is triggered. The LED cycle wil then start.
downUp = 2;
//clearStrip();
bottomup(); // lights up the strip from bottom up
}
//}
if (timeOut+10000 < millis() && timeOut+15000 < millis()) { //switch off LED's in the direction of travel.
if (downUp == 1) {
colourWipeDown(strip.Color(0, 0, 0), 100); // Off
}
if (downUp == 2) {
colourWipeUp(strip.Color(0, 0, 0), 100); // Off
}
downUp = 0;
for (int i=0 ;i < 35; i++) { // Depending on your preference you may want to include this loop to clear out the colourArray
colourArray[i]=0;
}
}
if (timeOut+15000 < millis() && timeOut+15999 > millis()) fade(); // Fade/switch off LED's
}
void topdown() {
Serial.println ("detected top"); // Helpful debug message
colourWipeDown(strip.Color(255,255,102), 25 ); // Warm White **** kleur keuze blauw *****
//for(int i=0; i<3; i++) { // Helpful debug indication flashes led on Arduino board twice
//digitalWrite(ledPin,HIGH);
//delay(200);
//digitalWrite(ledPin,LOW);
//delay(200);
//}
}
void idlePattern(uint32_t c, uint16_t wait){
for (uint16_t i=0; i<strip.numPixels(); i = i+35){ //nope
strip.setPixelColor(i,c);
strip.show();
delay(wait);
strip.setPixelColor(i,(0,0,0));
}
for (uint16_t j= strip.numPixels(); j>0; j = j-35){ //nope
strip.setPixelColor(j-1,c);
strip.show();
delay(wait);
strip.setPixelColor(j-1,(0,0,0));
}
}
void bottomup() {
Serial.println ("detected bottom"); // Helpful debug message
colourWipeUp(strip.Color(255,255,102), 25); // Warm White **** kleur keuze blauw ****
//for(int i=0; i<3; i++) { // Helpful debug indication flashes led on Arduino board twice
//digitalWrite(ledPin,HIGH);
//delay(200);
//digitalWrite(ledPin,LOW);
//delay(200);
//}
}
// Fade light each step strip
void colourWipeDown(uint32_t c, uint16_t wait) {
for (uint16_t j = 0; j < 16; j++){
int start = strip.numPixels()/16 *j;
//for(float b=0; b<=1; b = b+0.5){
for (uint16_t i = start; i < start + 35; i++){
strip.setPixelColor(i, c);
strip.show();
}
//delay(5);
//}
delay(wait);
}
}
void clearStrip(){
for (int l=0; l<strip.numPixels(); l++){
strip.setPixelColor(l, (0,0,0));
}
}
// Fade light each step strip
void colourWipeUp(uint32_t c, uint16_t wait) {
for (uint16_t j = 16; j > 0; j--){
int start = strip.numPixels()/16 *j;
//start = start-1;
//for(float b=0; b<=1; b = b+0.5){
for (uint16_t i = start; i > start - 35; i--){
strip.setPixelColor(i-1, c);
strip.show();
}
//delay(5);
//}
//Serial.println(j);
delay(wait);
}
}
// Play the LED fade out
void fade(){
for (int j = 0; j <70; j++) {
for(int i=350; i>-1; i--) {
colourArray[i]=colourArray[i]-1; // reduce intensity of light by 1
if (colourArray[i] <= 0 ) colourArray[i] = 0;
}
for (int k=0; k<351; k=k+3) {
uint32_t c = strip.Color(colourArray[k],colourArray[k+1],colourArray[k+2]);
strip.setPixelColor(((k+3)/3)-1,c);
}
strip.show();
delay(60);
}
breathe = 0;
change = 1;
}