[Rextytus]

Witam właśnie przeszedłem bądź prawie przeszedłem z jednej automatyki domowej do drugiej . A konkretnie z domoticza na home assistanta.
W domoticzu miałem załączanie ogrzewania na arduino uno + ethernet shield W5100 itam po mysensors 7 przekaźników działa od 6 lat .
W home assistancie niestety nie problem z mysensors , pod my sensors wgrałem sketch z obsługą mqtt i śmiga aż miło tyle ,że w tym sketchu są cztery przekaźniki i cztery przyciski . Przyciski są mi niepotrzebne ale wejścia przycisków mogłyby obsługiwać dodatkowo cztery przekaźniki i tu problem jak usunąć te cztery buttony ze sketch aby wszystko dalej działało ? Niby proste ale takich zapisów  z mqtt to niejestem pewien może ktoś pomoże i rozszyfruje zapisy?

Kod:

/*
Example MQTT-switch-relay-node with 4 buttons and 4 leds

  - connects to an MQTT server
  - publishes "hello world" to the topic "led"
  - subscribes to the topic "led"
  - controls 4 leds on pins 2,3,5 and 6 - leds can be replaced with relays
  - reads 4 button on pins 7,8,9 and 10
  - turns on/off a specific led when it receives a specific "on"/"off" from the "led" topic
  - sends a specific "on"/"off" to the "led" topic a specific button is pressed
  - multiple arduino's with same generic sketch can run parallel to each other
  - multiple arduino's need each to have a unique ip-addres, unique mac address and unique MQTT client-ID

  - tested on arduino-uno with W5100 ethernet shield
  - Ethernet Shield W5100 uses pins 4,10,11,12,13
  - availbale digital pins: 1,2,3,5,6,7,8,9,10
*/

//------------------------------------------------------------------------------

#include <SPI.h>
#include <Ethernet.h>
#include <PubSubClient.h>
#include <Bounce2.h>

// Set led variables to Arduino digital pins
int led1 = 2;
int led2 = 3;
int led3 = 5;                             // pin 4 used by ethernet shield
int led4 = 6;


// Set button variables to Arduino digital pins
int button1 = 7;
int button2 = 8;
int button3 = 9;
int button4 = 10;                         // pins 11,12,13 used by ethernetshield

// Set variables to act as virtual switches
// Set variable values initially to LOW (and not HIGH)
int led1Value = LOW;             
int led2Value = LOW;
int led3Value = LOW;
int led4Value = LOW;


//---------------------------------------------------------------------------

// Arduino MAC address is on a sticker on your Ethernet shield
// must be unique for every node in same network
// To make a new unique address change last letter

byte mac[]    = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xEE }; 

// Unique static IP address of this Arduino - change to adapt to your network
IPAddress ip(192,168,0,238);

// IP Address of your MQTT broker - change to adapt to your network
byte server[] = { 192, 168, 0, 20 };

// Handle and convert incoming MQTT messages ----------------------------------------

void callback(char* topic, byte* payload, unsigned int length) {
  // handle message arrived
  String content="";
  char character;
  for (int num=0;num<length;num++) {
      character = payload[num];
      content.concat(character);
  }   
  Serial.println(topic);
  Serial.println(content); // message sent out by button actions is returned from broker and serial printed


// Set specific virtual switches on basis of specific incoming messages ----------------------------
 
  if (content == "1on") {
    led1Value = HIGH;
  }
 
  if (content == "1off") {
    led1Value = LOW;
  }
 
  if (content == "2on") {
    led2Value = HIGH;
  }
 
  if (content == "2off") {
    led2Value = LOW;
  }

 
  if (content == "3on") {
    led3Value = HIGH;
  }
 
  if (content == "3off") {
    led3Value = LOW;
  }
 
  if (content == "4on") {
    led4Value = HIGH;
  }
 
  if (content == "4off") {
    led4Value = LOW;
  }
 
   
  // Set digital pin states according to virtual switch settings
   
  digitalWrite(led1,led1Value);
  digitalWrite(led2,led2Value);
  digitalWrite(led3,led3Value);
  digitalWrite(led4,led4Value);

}

// Initiate instances -----------------------------------

EthernetClient ethClient;
PubSubClient client(server, 1883, callback, ethClient);

// Initiate a bouncer instance for each button
Bounce bouncer1 = Bounce();
Bounce bouncer2 = Bounce();
Bounce bouncer3 = Bounce();
Bounce bouncer4 = Bounce();

//-------------------------------------------------------

void setup()

{

  // setup led, button, bouncer 1 -----------------------
  pinMode(led1, OUTPUT);
  pinMode(button1,INPUT);
  digitalWrite(button1,HIGH);
  bouncer1 .attach(button1);
  bouncer1 .interval(5);

  // setup led, button, bouncer 2 -----------------------
  pinMode(led2, OUTPUT);
  pinMode(button2,INPUT);
  digitalWrite(button2,HIGH);
  bouncer2 .attach(button2);
  bouncer2 .interval(5);

  // setup led, button, bouncer 3 -----------------------
  pinMode(led3, OUTPUT);
  pinMode(button3,INPUT);
  digitalWrite(button3,HIGH);
  bouncer3 .attach(button3);
  bouncer3 .interval(5);

  // setup led, button, bouncer 4 -----------------------
  pinMode(led4, OUTPUT);
  pinMode(button4,INPUT);
  digitalWrite(button4,HIGH);
  bouncer4 .attach(button4);
  bouncer4 .interval(5);

  // setup serial and ethernet communications -------------------------------

  // Setup serial connection
  Serial.begin(9600);

  // Setup ethernet connection to MQTT broker
  Ethernet.begin(mac);
  if (client.connect("arduino-ip-238")) {                              // change as desired - clientname must be unique for MQTT broker
    client.publish("led","hello world - here arduino ip 239");
    Serial.println("connected");
    client.subscribe("led");                                        // subscribe to topic "led"
  }
}

//----------------------------------------------

void loop()
{

// Listen for button interactions and take actions ---------------------------------------- 
// Note: Button actions do send MQTT message AND do set led(x)Value to HIGH or LOW

  if (bouncer1.update()) {
    if (bouncer1.read() == HIGH) {
      if (led1Value == LOW) {
        led1Value = HIGH;
        client.publish("led","1on");                                
      } else {
        led1Value = LOW;
        client.publish("led","1off");
      }
    }
  } 

//-----------------------------------------------
 
  if (bouncer2.update()) {
    if (bouncer2.read() == HIGH) {
      if (led2Value == LOW) {
        led2Value = HIGH;
        client.publish("led","2on");
      } else {
        led2Value = LOW;
        client.publish("led","2off");
      }
    }
  } 
 
//------------------------------------------------ 

  if (bouncer3.update()) {
    if (bouncer3.read() == HIGH) {
      if (led3Value == LOW) {
        led3Value = HIGH;
        client.publish("led","3on");
      } else {
        led3Value = LOW;
        client.publish("led","3off");
      }
    }
  } 

//-----------------------------------------------
 
  if (bouncer4.update()) {
    if (bouncer4.read() == HIGH) {
      if (led4Value == LOW) {
        led4Value = HIGH;
        client.publish("led","4on");
      } else {
        led4Value = LOW;
        client.publish("led","4off");
      }
    }
  } 
 
//------------------------------------------------ 
 
  client.loop();
}

// End of sketch ---------------------------------

[powerTGS]

To prosty kod, dopisz swoje, usuń zbędne - w czym problem ?